Just How to Set up a Bath Tub
Just How to Set up a Bath Tub
Blog Article
The article author is making several good points on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround overall in the content just below.
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is conveniently accessible, the task can relocate immediately; if you need to open a wall to remove the old bathtub and also position the new bathtub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. Make sure you have actually certified on your own for the work as well as are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Opportunities are you may need a professional plumber to make tube links.
This post will aid you mount a new bathtub in your washroom if you have already purchased a brand-new tub and do not need to transform the setup of your previous supply of water pipes.
Your devices as well as material list must make up the following:
Getting ready for the Installation
To start with, the supporting framework supplied with the bathroom must be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to avoid pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its final setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, after that the first thing you should do is disconnect the supply of water. After doing so, switch on the faucets to drain pipes any water staying in the system. The process of eliminating the existing faucets can be fairly problematic due to the restricted gain access to that is commonly the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four little points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level and readjusting the feet on the bath tub till the level checks out level.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the proper supply pipe by making a compression join; after that do the exact same for the other tap.
Switch on the water and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and also the typical outlet for leakages.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bath tub must wait until the bath tub has actually been used at the very least when as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Safeguard the tap in position with the producer given backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bathroom meets the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to issues with wetness and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill up the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealant can break relatively very early if you do not think about this movement before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly offered on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I'm hoping you enjoyed our post. Sharing is nice. Helping others is fun. Thanks for your time spent reading it.
Visit Site
Report this page